Ebtron Airflow Monitor Station - Revision history

Timm at 21:46, 22 January 2020

2020-01-22T21:46:13Z

← Older revision		Revision as of 21:46, 22 January 2020
Line 29:		Line 29:
	It is possible to use a single AFMS for multiple OA intake dampers (e.g. OA intake dampers on each side of the unit).  If this is the case, Ebtron must be notified that the AFMS will be used on more than one damper, so they can determine the correct number of probes and sensors.		It is possible to use a single AFMS for multiple OA intake dampers (e.g. OA intake dampers on each side of the unit).  If this is the case, Ebtron must be notified that the AFMS will be used on more than one damper, so they can determine the correct number of probes and sensors.

	Also, make certain the requested cable length is adequate to run from the probes to the location of the AFMS controller.  A 25' cable is our ~~stadand~~ length, but 50' is available if needed.  If the unit's control panel is a relatively far distance away from the AFMS probes, a separate panel is installed for the AFMS controller.		Also, make certain the requested cable length is adequate to run from the probes to the location of the AFMS controller.  A 25' cable is our standard length, but 50' is available if needed.  If the unit's control panel is a relatively far distance away from the AFMS probes, a separate panel is installed for the AFMS controller.

Timm at 21:26, 22 January 2020

2020-01-22T21:26:34Z

← Older revision		Revision as of 21:26, 22 January 2020
Line 2:		Line 2:
	'''<u><span style="font-size:larger;">Basic Ebtron Info</span></u>'''		'''<u><span style="font-size:larger;">Basic Ebtron Info</span></u>'''

	Ebtron airflow monitoring stations (AFMS) are typically mounted on the OA intake damper when specified for the job.  They can also be used to measure CFM on any damper type, coil face area, blower inlet, etc.  The GTA116-PC model is the standard for S-4.  An AFMS uses a series of probes and sensors to measure the airflow through the damper.  <span style="color:#e74c3c;">''(ADD MORE TECHNICAL INFO HERE - TDM; 1/22/20)''</span>.		Ebtron airflow monitoring stations (AFMS) are typically mounted on the OA intake damper when specified for the job.  They can also be used to measure CFM on any damper type, coil face area, blower inlet, etc.  The GTA116-PC model is the standard for S-4, and our standard part numbers starts with 4091530<u>xxx</u>.  An AFMS uses a series of probes and sensors to measure the airflow through the damper.  <span style="color:#e74c3c;">''(ADD MORE TECHNICAL INFO HERE - TDM; 1/22/20)''</span>.


Line 29:		Line 29:
	It is possible to use a single AFMS for multiple OA intake dampers (e.g. OA intake dampers on each side of the unit).  If this is the case, Ebtron must be notified that the AFMS will be used on more than one damper, so they can determine the correct number of probes and sensors.		It is possible to use a single AFMS for multiple OA intake dampers (e.g. OA intake dampers on each side of the unit).  If this is the case, Ebtron must be notified that the AFMS will be used on more than one damper, so they can determine the correct number of probes and sensors.

	Also, make certain the requested cable length is adequate to run from the probes to the location of the AFMS controller.  If the unit's control panel is a relatively far distance away from the AFMS probes, a separate panel is installed for the AFMS controller.		Also, make certain the requested cable length is adequate to run from the probes to the location of the AFMS controller.  A 25' cable is our stadand length, but 50' is available if needed.  If the unit's control panel is a relatively far distance away from the AFMS probes, a separate panel is installed for the AFMS controller.

Timm at 21:20, 22 January 2020

2020-01-22T21:20:44Z

← Older revision		Revision as of 21:20, 22 January 2020
Line 138:		Line 138:
	<span style="font-size:larger;"><u>'''Example Email #3 - Multiple Locations in a Single Unit'''</u></span>		<span style="font-size:larger;"><u>'''Example Email #3 - Multiple Locations in a Single Unit'''</u></span>

	'''<span style="font-size:10.0pt"><span style="font-family:">From:</span></span>'''<span style="font-size:10.0pt"><span style="font-family:">Tim Morris<br/> '''Sent:''' Wednesday, June 13, 2012 1:04 PM<br/> '''To:''' Rick Rothschild<br/> '''Subject:''' FO #B223 Ebtron Ordering Info~~<br/> '''Importance:''' High~~</span></span>		'''<span style="font-size:10.0pt"><span style="font-family:">From:</span></span>'''<span style="font-size:10.0pt"><span style="font-family:">Tim Morris<br/> '''Sent:''' Wednesday, June 13, 2012 1:04 PM<br/> '''To:''' Rick Rothschild<br/> '''Subject:''' FO #B223 Ebtron Ordering Info</span></span>

Timm at 21:19, 22 January 2020

2020-01-22T21:19:50Z

← Older revision		Revision as of 21:19, 22 January 2020
Line 32:		Line 32:



			----

	<span style="font-size:larger;"><u>'''Example Email #1'''</u></span>		<span style="font-size:larger;"><u>'''Example Email #1'''</u></span>
Line 99:		Line 101:



			----

	<span style="font-size:larger;"><u>'''Example Email #2 - One (1) AFMS for Two (2) OA Dampers'''</u></span>		<span style="font-size:larger;"><u>'''Example Email #2 - One (1) AFMS for Two (2) OA Dampers'''</u></span>
Line 129:		Line 133:



			----

	<span style="font-size:larger;"><u>'''Example Email #3 - Multiple Locations in a Single Unit'''</u></span>		<span style="font-size:larger;"><u>'''Example Email #3 - Multiple Locations in a Single Unit'''</u></span>

Timm at 15:17, 22 January 2020

2020-01-22T15:17:42Z

← Older revision		Revision as of 15:17, 22 January 2020
Line 100:		Line 100:


	<span style="font-size:larger;"><u>'''~~Email~~ Example #2 - One (1) AFMS for Two (2) OA Dampers'''</u></span>		<span style="font-size:larger;"><u>'''Example Email #2 - One (1) AFMS for Two (2) OA Dampers'''</u></span>

	'''<span style="font-size:10.0pt"><span style="font-family:">From:</span></span>'''<span style="font-size:10.0pt"><span style="font-family:">Tim Morris<br/> '''Sent:''' Thursday, September 11, 2014 11:16 AM<br/> '''To:''' Robert Koon<br/> '''Subject:''' FO #B866 Ebtron Ordering Info</span></span>		'''<span style="font-size:10.0pt"><span style="font-family:">From:</span></span>'''<span style="font-size:10.0pt"><span style="font-family:">Tim Morris<br/> '''Sent:''' Thursday, September 11, 2014 11:16 AM<br/> '''To:''' Robert Koon<br/> '''Subject:''' FO #B866 Ebtron Ordering Info</span></span>

Timm at 14:44, 22 January 2020

2020-01-22T14:44:50Z

← Older revision		Revision as of 14:44, 22 January 2020
Line 2:		Line 2:
	'''<u><span style="font-size:larger;">Basic Ebtron Info</span></u>'''		'''<u><span style="font-size:larger;">Basic Ebtron Info</span></u>'''

	Ebtron airflow monitoring stations (AFMS) are typically mounted on the OA intake damper when specified.  They can also be used to measure CFM on any damper type, coil face area, blower inlet, etc.  The GTA116-PC model is the standard for S-4.  An AFMS uses a series of probes and sensors to measure the ~~aiflow~~ through the damper.  <span style="color:#e74c3c;">''(ADD MORE TECHNICAL INFO HERE - TDM; 1/22/20)''</span>.		Ebtron airflow monitoring stations (AFMS) are typically mounted on the OA intake damper when specified for the job.  They can also be used to measure CFM on any damper type, coil face area, blower inlet, etc.  The GTA116-PC model is the standard for S-4.  An AFMS uses a series of probes and sensors to measure the airflow through the damper.  <span style="color:#e74c3c;">''(ADD MORE TECHNICAL INFO HERE - TDM; 1/22/20)''</span>.


Line 14:		Line 14:
	*Damper Size (width x height).		*Damper Size (width x height).
	**Note: This is <u>total </u>damper size if more than one damper are used for a single AFMS.		**Note: This is <u>total </u>damper size if more than one damper are used for a single AFMS.
	**E.G. 48" x 60" ~~toal~~ size for two (2) individual 24" x 60" dampers.		**E.G. 48" x 60" total size for two (2) individual 24" x 60" dampers.
	*Mounting Type (e.g. Stand-off mounting).		*Mounting Type (e.g. Stand-off mounting).
	*Cable Length (e.g. 25')		*Cable Length (e.g. 25')
Line 20:		Line 20:
	*Face Velocity (FPM) thru Damper @ Max CFM.		*Face Velocity (FPM) thru Damper @ Max CFM.
	*Drawing showing the location of the AFMS in the unit.		*Drawing showing the location of the AFMS in the unit.
	*Job Location (i.e city, state).		*Job Location (i.e. city, state).
	*Seasons-4 Part Number(s)		*Seasons-4 Part Number(s)



	When ordering the AFMS, it is ~~prefered~~ that Ebtron determines the required number of probes and sensors.  Our part number descriptions will not show this info for all future new P/N setups.  Any existing P/N that has the correct damper size for your application can be used, but it is recommended that any detail describing the number or probes, sensors and cable length be removed from the ~~exsting~~ P/N descriptions.  Ask Purchasing to make this change before issuing the P.O.		When ordering the AFMS, it is preferred that Ebtron determines the required number of probes and sensors.  Our part number descriptions will not show this info for all future new P/N setups.  Any existing P/N that has the correct damper size for your application can be used, but it is recommended that any detail describing the number or probes, sensors and cable length be removed from the existing P/N descriptions.  Ask Purchasing to make this change before issuing the P.O.

	It is possible to use a single AFMS for multiple OA intake dampers (e.g. OA intake dampers on each side of the unit).  If this is the case, Ebtron must be notified that the AFMS will be used on more than one damper, so they can determine the correct number of probes and sensors.		It is possible to use a single AFMS for multiple OA intake dampers (e.g. OA intake dampers on each side of the unit).  If this is the case, Ebtron must be notified that the AFMS will be used on more than one damper, so they can determine the correct number of probes and sensors.

Timm at 14:36, 22 January 2020

2020-01-22T14:36:46Z

← Older revision		Revision as of 14:36, 22 January 2020
Line 9:		Line 9:

	When ordering an Ebtron AFMS, you must send the design info to Purchasing, so they can add details to the P.O. and relay the info to Ebtron.  When ordering, you must include:		When ordering an Ebtron AFMS, you must send the design info to Purchasing, so they can add details to the P.O. and relay the info to Ebtron.  When ordering, you must include:



	*Damper Size (width x height).		*Damper Size (width x height).

Timm at 14:35, 22 January 2020

2020-01-22T14:35:56Z

← Older revision		Revision as of 14:35, 22 January 2020
Line 148:		Line 148:
	Here is a description of each required airflow station:		Here is a description of each required airflow station:

	#<u>P/N 4091530167 (Qty 1)</u> ~~<ol start="1" style="list-style-type: lower-alpha;">~~		#<u>P/N 4091530167 (Qty 1)</u>
	~~<li>~~Measures a 30” x 30” OA damper~~.</li>~~		##Measures a 30” x 30” OA damper
	~~<li>~~Standoff Mounting~~</li>~~		##Standoff Mounting
	~~<li>~~25’ Wire Length~~</li>~~		##25’ Wire Length
	</ol> </ol>


	<ol start="2">		<ol start="2">
	<li><u>P/N 4091530167 (Qty 1)</u> <ol style="list-style-type:lower-alpha">		<li><u>P/N 4091530167 (Qty 1)</u> <ol style="list-style-type:lower-alpha">
	<li>Measures a 30” x 30” SC coil face ~~are~~</li>		<li>Measures a 30” x 30” SC coil face area</li>
	<li>Standoff Mounting</li>		<li>Standoff Mounting</li>
	<li>25’ Wire Length</li>		<li>25’ Wire Length</li>

Timm at 14:32, 22 January 2020

2020-01-22T14:32:11Z

Show changes

Timm at 14:15, 22 January 2020

2020-01-22T14:15:44Z

← Older revision		Revision as of 14:15, 22 January 2020
Line 2:		Line 2:
	'''<u><span style="font-size:larger;">Basic Ebtron Info</span></u>'''		'''<u><span style="font-size:larger;">Basic Ebtron Info</span></u>'''

	Ebtron airflow monitoring stations (AFMS) are typically mounted on the OA intake damper when specified.  The GTA116-PC model is the standard for S-4.  ~~The monitoring stations~~ uses a series of probes and sensors to measure the aiflow through the damper.  <span style="color:#e74c3c;">''(ADD MORE TECHNICAL INFO HERE - TDM; 1/22/20)''</span>.		Ebtron airflow monitoring stations (AFMS) are typically mounted on the OA intake damper when specified.  The GTA116-PC model is the standard for S-4.  An AFMS uses a series of probes and sensors to measure the aiflow through the damper.  <span style="color:#e74c3c;">''(ADD MORE TECHNICAL INFO HERE - TDM; 1/22/20)''</span>.


Line 8:		Line 8:
	<span style="font-size:larger;"><u>'''Ordering Info'''</u></span>		<span style="font-size:larger;"><u>'''Ordering Info'''</u></span>

	When ordering an Ebtron ~~aiflow measuring station~~, you must send the design info to Purchasing, so they can add details to the P.O. and relay the info to Ebtron.  When ordering ~~an Ebtron airflow station~~, you must include:		When ordering an Ebtron AFMS, you must send the design info to Purchasing, so they can add details to the P.O. and relay the info to Ebtron.  When ordering, you must include:

	*Damper Size (width x height).		*Damper Size (width x height).
			**Note: This is <u>total </u>damper size if more than one damper are used for a single AFMS.
			**E.G. 48" x 60" toal size for two (2) individual 24" x 60" dampers.
	*Mounting Type (e.g. Stand-off mounting).		*Mounting Type (e.g. Stand-off mounting).
	*Wire Length (e.g. 25')		*Wire Length (e.g. 25')
Line 17:		Line 19:
	*Drawing showing the location of the AFMS in the unit.		*Drawing showing the location of the AFMS in the unit.
	*Job Location (i.e city, state).		*Job Location (i.e city, state).
			*Seasons-4 Part Number(s)



	When ordering the AFMS, it is prefered that Ebtron determines the required number of probes and sensors.  Our part number descriptions will not show this info for all future new P/N setups.  Any existing P/N that has the correct damper size for your application can be used, but it is recommended that any detail describing the number or probes, sensors and wire length be removed from the exsting P/N descriptions.  Ask Purchasing to make this change before issuing the P.O.		When ordering the AFMS, it is prefered that Ebtron determines the required number of probes and sensors.  Our part number descriptions will not show this info for all future new P/N setups.  Any existing P/N that has the correct damper size for your application can be used, but it is recommended that any detail describing the number or probes, sensors and wire length be removed from the exsting P/N descriptions.  Ask Purchasing to make this change before issuing the P.O.

			It is possible to use a single AFMS for multiple OA intake dampers (e.g. OA intake dampers on each side of the unit).  If this is the case, Ebtron must be notified that the AFMS will be used on more than one damper, so they can determine the correct number of probes and sensors.

			Also, make certain the requested wire length is adequate to run from the probes to the location of the AFMS controller.  If the unit's control panel is a relatively far distance away from the AFMS probes, a separate panel is installed for the AFMS controller.